/*
 * Configuration values for ModularWeatherStation
 *
 * Copyright (C) 2021 Gergely Polonkai
 * Author: Gergely POLONKAI <gergely@polonkai.eu>
 *
 * ModularWeatherStation is free software: you can redistribute it
 * and/or modify it under the terms of the GNU General Public License
 * as published by the Free Software Foundation, either version 3 of
 * the License, or (at your option) any later version.
 *
 * ModularWeatherStation is distributed in the hope that it will be
 * useful, but WITHOUT ANY WARRANTY; without even the implied warranty
 * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 * As additional permission under GNU GPL version 3 section 7, you may
 * distribute non-source form of the Program without the copy of the
 * GNU GPL normally required by section 4, provided you inform the
 * receipents of GNU GPL by a written offer.
 *
 */

#include "consts.h"

// The SSID (name) and password of the WiFi network you want to connect to
#define WIFI_SSID "YourWiFiName"
#define WIFI_PASS "YourWiFiPass"

// The system name will be the name your station is available as.  This
// should be different for each station you install (e.g. if you want to
// measure the temperature and humidity of each room separately)
//
// If mDNS is enabled (ie. in HTTP pull mode), this will be the advertised
// hostname.
//
// If MQTT is enabled, this will be the MQTT client ID.
#define SYSTEM_NAME "internal-hostname"

// The mode this system should run in.  See consts.h for the available values.
#define SYSTEM_MODE MODE_PROM_PULL

// If you have a DHT temperature+humidity sensor of this type will be used,
// remove the #undef line and uncomment one of DHT11 or DHT22.  You also have
// to define the PIN your DHT sensor’s data (usually marked as DAT) is
// connected to.
//
// DHT11 sensors are usually blue, and don’t work under freezing point
// (0°C/32°F)
//
// DHT22 sensors are usually white and slightly bigger than DHT11 ones.  They
// work well under freezing point (usually above -40°C/-40°F)
#undef DHT_TYPE
//#define DHT_TYPE DHT11
//#define DHT_TYPE DHT22
//#define DHT_PIN D5

// If you have a rain sensor (FC-37 or YL-83), connect its digital pin (not the
// analogue one!), remove the #undef line, and uncomment and change the
// #define RAIN_PIN line
#undef RAIN_PIN
//#define RAIN_PIN D0

// Pins used for I²C communication.  You will be instructed below if you need
// to uncomment these
//#define I2C_SDA_PIN D1
//#define I2C_SCL_PIN D2

// If you have a BH1750 light level sensor, remove this #undef line and
// uncomment the #define HAVE_BH1750 line.  You will also have to set the SDA
// and SCL pins using the I2C_SDA_PIN and I2C_SCL_PIN defines above.
#undef HAVE_BH1750
//#define HAVE_BH1750

// If you have a BMP180 or BMP085 pressure + temperature sensor, remove this
// #undef line and uncomment the #define HAVE_BMP180 line.  You will also have
// to set the SDA and SCL pins using the I2C_SDA_PIN and I2C_SCL_PIN defines
// above.
#undef HAVE_BMP180
// #define HAVE_BMP180